I am using the AcuRite internet bridge with a 5 in 1. The bridge crapped out on me. 2 weeks to send and receive a new one back. Then my pc crapped out on me. I could not for the life of me create a bridge again to use Kevin keys bridge reader with the new pc and clean install of windows 7. Gave up and bought a D-Link DIR-505 and flashed Meteobridge with a license. Working perfectly. Uploading to WU, PWS and CWOP no problems. The Acurite stuf is very limited to the software that can be used with it. I was outputting the data to a CSV file through Kevin Keys bridge reader that WD read. Do you have any plans to support Meteobridge?
Com port 1 is the only one available and selected. Under TCP/IP Connection to Davis VP/Vue IP /VVP/Meteohub I put the IP to log into Meteohub Port 1 and checked use with Meteohub. No option for Meteobridge.
When I click on Show connected devices I get this error:
GetAdaptersAddresses failed with error #87
humm
it should info about accessing meteohub
post a screen shot of the meteohub settings from the com port setup
or .zip and email me your settings files (see the FAQ on how to do that)
I didn’t have (enabled) checked off along with (use with meteohub). The meteohub data access: line just keeps repeating. Also when starting WD a current status windows pops up. Getting missed data. Just keeps saying increase time.
This is what I’m getting now under debug info:
Doing checking of time zone calculation
Daylight saving in use
Loaded all time records
Date /time (PC) that WD was last running is: 06/19/2015 16:43:00
converted to UTC Date /time that WD was last running is: 20150619204300
getting missed data initial 20150619204300 20150619204400
[10061] Connection refused
[10061] Connection refused
[10061] Connection refused
[10061] Connection refused
[10061] Connection refused
[10061] Connection refused
Doing checking of time zone calculation
Daylight saving in use
meteohub data access:->http://192.168.29.246:1/meteolog.cgi?mode=data&type=xml&start=20150619205900&end=20150619210000
[10061] Connection refused
But this is a METEOHUB command not supported by Meteobridge.
And as Meteobridge has no storage for detailed weather-data I think it can not accept a timeframe for historical data anyway either.
I never added the port number in the ip address. 1 was selected by default
and is the only com port available according to WD. I just put 192.168.29.246
with 0 and also backed spaced 0 out but WD keeps adding 0 back in. I also tried
Wim van der Kuil’s ip suggestion.
getting missed meteohub data 20150624182400 20150624182500
OK
Not Found
OK
and a rapidly flashing message that cannot be read because it is flashing to fast.
I have to unckeck enabled and restart WD. Then on restart with enabled unchecked
under debug info:
getting missed meteohub data 20150624182400 20150624182500
OK
Not Found
OK
( connected OK to com port 1 ) only appears under debug info after enabled is
unchecked and WD is restarted.
I ran Advanced port scanner.
Under 192.168.29.246 ports (scanned 67 of 67, opened:3 closed:64)
open ports (3)
22 open (ssh)
53 open (domain)
80 open (www-http)
closed ports (64)
0 - 21 closed
23 - 52 closed
54 - 79 closed
81 - 65535 closed
Hi
the not found error points to the IP address not being correct somehow
can you post a screen shot of the com port setup , meteobridge setup?
also have you tried build 81?
thanks
com/ip port
comm port setup
com port 1 selected by default and only port shown as available
Please bear with me on this not understanding this at all. Apparently I’m confusing com port and port numbers.
I only looked under comport number because of the info under debug info.
getting missed meteohub data 20150623182900 20150623183000
OK
Not Found
OK
connected OK to com port 1
As for using port 80, this is what I get with port 80 under debug info
I think it can work. The xml packages are quite similar.
Only Meteobrisdge needs a userid:password@ before the ip-address. Meteohub does not need that.
As I said Meteobridge does not support historical data. It has no memory, as only Meteohub has local memory to store historical data.
So the message “Not found” is the logical conclusion WD for the missing historical data. But they can also be missing for other reasons, so WD will be used to stations not supplying missing data.
Then it connects again to the Meteobridge using WD-internal-port1 (which, i think, is connected to => 192.168.29.246:80)
So what happens after “connected OK to com port 1”
The question is: Is there any data arriving in WD ? Is the dashboard showing data for temperature and so on?
If it does not show any data, try to add that userid:password@ part before your 192.168.29.246 and see if the data is shown then.
And very soon Brian will wake up again on the other side of the globe to help you further.